Nope, doesn't matter if HDDs are connected or not, the problem persists >.< Should I try these one at a time, in a certain order, or not at all?Įdit: FLASHSPI.EXE/M770TUD3.F8B/C/E/D didn't help.
I do the same again with the above commands after it and it that Flashes again and performs the extra function.
HP DMI TOOL CANT READ UPDATE
D - Load CMOS Defaults after BIOS Update Running FLASHSPI.EXE brings up a list of commands M770TUD3.F8B (the flash's data that the Flash ultility wanted) I DIR to see the files on the disk as instructed to put there.ĪUTOEXEC.BAT (autoruns the EXE with the FB8 and flashes when I boot from the drive) That should be enough flashing right? Well anyhow, I tried to flash it from the USB Boot disk, no luck either.Īs a side thought, there are extra functions in DOS for me: There's also a Quick Flash function which also didn't fix it. Like it told me I'd have to press a key to continue where I didn't, afterwards there was no confirmation, the box just disappeared, all just subtle differences. I flashed the update thingy with the interface for doing so as directed in the manual, however it didn't go as per the instructions. Which should I choose? I've tried both many times to no avail. "Įdit: Now only Profile 1 is ever there but I also noticed the button at the bottom telling me I can press F1 to continue with boot. However, if I don't press Del when I reset it, I hang at "Verifying DMI Pool Data.
I've been trying this for ages now, and it turns out that when I do successfully reset CMOS, if I press Del for BIOS then a screen comes up saying CMOS had a Checksum Error and that I can load Profile 1 or last known good settings. Btw, just an act of stupidity, but if u tap the CMOS reset while computer is on, it actually does it. any ideas plz?Ĭlick to expand.Ok, I tried that a few times. That's all I can think of that you need to know. "How about clearing the CMOS with the jumper on the board?" - What the bajeezus? Sounds like heart surgery to me. "I've seen this issue mentioned in other places and some people have said that it's nothing to worry about" - So perhaps computers with this error normally boot into their OS then? Cus I'm worrying. "You can make sure you are running the latest BIOS version" - How.? Tips from the thread linked at the top that I don't understand/couldn't try/can anyone explain how? Any company will take days to reply and probably just tell me to try something I already tell them I tried followed by a load of advertising. Searching Google for solutions/Technical Support: Original error is still there and of-course the NTLDR error which I fix by reconnecting them in the right order. "AMD Data Change.Update New Data to DMI! Update Success" but still does nothing more than sit there. (Will look for more detailed names if anyone thinks it necessary just say so)
HP DMI TOOL CANT READ PRO
Had a major virus outbreak on another computer using AVG (this one uses Norton), and have copied files between them despite reappearances of the viruses.ġTB SATA HDD (Partitioned to 100gb (C for Windows XP SP3 x32, the first OS installation, and 900gb (E for data.Ĥ0GB IDE HDD for Windows 7 Pro 圆4, second OS installation Installed several programs of the Adobe CS5 Creative Suite. Closed it.Ībout 10 hours later it was still working perfectly, I turned off the computer and went to sleep.
HP DMI TOOL CANT READ SOFTWARE
Powerquest Partition Magic and their Diskkeeper software that comes with it: PM said it has compatibility issues, opened it but did nothing with it.ĭiskkeeper wanted to just back up my system to a floppy drive. What's changed since the last successful boot: so if you want to play it sooner you'l help me get this working faster Also, it is quite urgent as I'm the lead modeller on Cypherium and am falling behind schedule. I appreciate any time you put in to helping me here. Unfortunately some smartypants decided to close the thread (or set automatic thread closing) so no reply notifications can go directly to the people originally dealing with the problem, leaving us with no choice but to have a duplicate thread and a restart on the expertise involved in solving it I've been reading this post as it's the only thing I could find on the net about my problem. Basically, I get that message "AMD Data Change.Update New Data to DMI!" then it just hangs there no matter how long I leave it.